Oil based. Penetrates to colour and enhance the beauty of wood. Stains and seals in one easy step. For any interior unfinished wood surfaces.

Minwax® Wood Finish™ is an oil-based wood stain that provides long-lasting wood tone color. It penetrates deep into the pores to seal and protect the wood. Minwax® Wood Finish™ is available in 22 wood tone colors and can be used to enhance any bare or stripped wood surface. It is ideal for staining furniture, cabinets, doors, trim, molding, and hardwood floors.

Application tool: brush, cloth or foam applicator
Location: interior wood surfaces
Dry time: 8 hours
Recoat: 4-6 hours
Cleanup: mineral spirits
Coverage: 150 sq. ft. per quart
Coats: normally 2. Additional coats may be applied for richer color
Recommended uses: furniture, woodwork, doors, floors, cabinets, accessories.

The colors shown are for reference purposes only. They have been reproduced using digital production techniques. Always test stain on a hidden area of the wood to verify desired color.

FAQ:

Q. How long should Minwax® Wood Finish™ be left on the wood?
Anywhere from a few seconds to 15 minutes. The longer the stain is left on the wood, the deeper it will penetrate. For a light tint, wipe the excess stain off after a few minutes; for deeper, richer color, wait as long as 15 minutes.

Q. Why is it important to wipe off the excess stain?
The colorants in Minwax® Wood Finish™ are designed to be deposited in the wood pores, not on the surface of the wood. Any pigments allowed to remain on top of the wood will impair topcoat adhesion - causing the finish to peel.

Q. Is it necessary to sand after the Minwax® Wood Finish™ has dried?
No. In fact, we advise against it. Sanding will result in the removal of some of the dyes and pigments in the stained wood. Since Minwax® Wood Finish™ does not raise the grain, no sanding is necessary before top-coating.

Q. Does Minwax® Wood Finish™ need to be top-coated?
For added beauty and protection, we recommend topcoating all projects with a protective clear finish such as Minwax® Fast-Drying Polyurethane or Minwax® Polycrylic® Protective Finish.

Q. Can Minwax® Wood Finish™ colors be mixed to create additional colors?
There may be times when a desired stain color can only be achieved by mixing two colors. Experiment with different proportions until the desired color is achieved. Then mix enough stain to complete the entire project to avoid color-matching later.

Q. Why don't some woods match the colors on the Minwax® product brochures and samples?
Wood can vary in color and pore structure even within the same species. Because every piece of wood is unique, final stain color may vary. While our samples are tested for accuracy, it is always best to first test Minwax® Wood Finish™ on a small, inconspicuous spot on the project.

DIRECTIONS

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup.

SURFACE PREPARATION:

Sand the wood in the direction of the grain, first using medium grade sandpaper (#120) and working your way to fine-grade (#220). Remove all sanding dust before staining.
Pre-treat soft or porous woods such as pine, maple, alder and birch with Minwax® Pre-Stain Wood Conditioner. This will help the wood evenly absorb stain color. Apply stain within two hours of pre-treatment.

PRODUCT PREPARATION & COLOR TESTING:

Stir stain thoroughly before and occasionally during use.
Test stain on a hidden area to verify desired color.
To lighten any color, add Minwax® Wood Finish™ 209 Natural to the mixture.

STAIN APPLICATION:

Apply Wood Finish™ in the direction of the grain with a brush or clean cloth.
Let the stain penetrate 5 -15 minutes to ensure you achieve the desired color.
Remove excess stain with a clean cloth. Wipe in the direction of the grain, while blending light and dark areas to obtain uniform color.
To Darken color, apply a second coat after 4-6 hours, repeating application directions of first coat.
Dry times may be extended due to high humidity, low temperatures or inadequate ventilation.

CLEAR FINISH APPLICATION:

After a minimum of 8 hours, apply a clear, protective finish such as Minwax® Fast-Drying Polyurethane, Minwax® Helmsman® Spar Urethane or after 24 hours, apply clear Minwax® Polycrylic® Protective Finish.

Water cleanup clear finishes such as Minwax® Polycrylic® Protective Finish should not be used over Minwax® Wood Finish™ Red Mahogany stain. Minwax® Wood Finish™ Pickled Oak should be top-coated only with a water cleanup clear finish such as Minwax® Polycrylic® Protective Finish. Do not top-coat Minwax® Wood Finish™ Pickled Oak with an oil-based clear finish as ambering will occur.

Minwax® Gel Stain is a non-drip stain that adds natural colors and accentuates the beauty of a wide range of wood and non-wood surfaces
including wood, plywood, veneer, fiberglass, metal and molded fiberboard. Minwax® Gel Stain is ideal for vertical applications like doors and molding.

Application tool: brush, cloth or foam applicator
Location: interior or exterior* surfaces
(* must be top-coated with an exterior clear top-coat)
Dry time: 24 hours
Recoat: 8-10 hours
Cleanup: mineral spirits
Coverage: 200 sq. ft. per quart
Coats: 1-2 depending on the surface
Recommended uses: woodwork, furniture, doors, cabinets, accessories

The colors shown are for reference purposes only. They have been reproduced using digital production techniques. Always test stain on a hidden area of the wood to verify desired color.

FAQ:

Q. What makes this Minwax® Gel Stain product different from traditional stains such as Minwax® Wood Finish™?
As its name implies, Gel Stain has a gelled consistency. The non-drip formula makes it an ideal choice for vertical surfaces. Because it is thick-bodied, it stays more toward the surface of the wood, allowing greater color control during application. In addition, Gel Stain can be applied to non-wood surfaces, including metal and fiberglass, to give them a beautiful wood appearance.

Q. Does Minwax® Gel Stain need to be top-coated?
For added beauty and protection, we recommend topcoating all interior projects with a protective clear finish such as Minwax® Fast Drying Polyurethane or Minwax® Polycrylic Protective Finish. For exterior applications, use Minwax® Helmsman® Spar Urethane.

Q. What's the best way to apply Gel Stain to a fiberglass door?
Fiberglass is non-porous and won't absorb the stain the way a wood surface does. So, it's best to apply Gel Stain with a bristle brush. Excess Stain should be evened out with the brush - not wiped away with a rag. See application instructions on this website.

Q. Should Pre-Stain Wood Conditioner be used with Gel Stain?
Yes, if the wood being stained is soft or porous. Soft or porous woods, such as pine or aspen, tend to absorb stains unevenly. Before using Gel Stain on soft or porous woods, Pre-Stain Wood Conditioner should be applied to ensure even stain penetration.

DIRECTIONS

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup.

WOOD SURFACE DIRECTIONS:

SURFACE PREPARATION:

Make sure the surface is clean and free of dirt, grease and old coatings.
To help ensure even stain color penetration and beautiful results, pre-treat soft or porous woods such as pine, maple, alder and birch with Minwax® Pre-Stain Wood Conditioner.
Apply Minwax® Pre-Stain Wood Conditioner, allow to penetrate for 5-15 minutes, then wipe off excess. Apply Minwax® Gel Stain within 2 hours of pretreatment.

STAIN APPLICATION:

Before use and occasionally throughout project, stir Minwax® Gel Stain until creamy.
Test stain on hidden area to verify desired color.
Apply a liberal amount of Minwax® Gel Stain evenly with a brush or rag. Wait 3 minutes and, using a clean rag, wipe with the wood grain to remove the excess. Allow to dry 8 to 10 hours.
To darken the color, apply additional coats of Minwax® Gel Stain following the instructions above. Allow the stain to dry 8 to 10 hours between coats.

CLEAR FINISH APPLICATION:

After 24 hours, apply a Minwax® protective clear finish. For interior wood use Minwax® Fast Drying Polyurethane or Minwax® Polycrylic Protective Finish. For exterior use we recommend Minwax® Helmsman® Spar Urethane.
FIBERGLASS DOORS DIRECTIONS:

For ease of staining and finishing we recommended that you finish the door before installation. If you are finishing a pre-hung door, allow enough time in each of the application steps for the door to dry (at least 6 to 8 hours) to avoid sticking. The door should not be closed during the drying/curing process.

SURFACE PREPARATION:

Make sure the door surface is free of all dirt and foreign matter. Use a rag moistened with mineral spirits to remove dirt and scuff marks left on the door during shipping and handling.
Before applying, stir Minwax® Gel Stain to break up its gel consistency. Then, reseal the container and shake Gel Stain vigorously for at least 30 seconds. This will thin Gel Stain into a syrup-like consistency.

STAIN APPLICATION:

Test stain on hidden area to verify desired color.
Using a high quality natural bristle brush, spread a thin, even coat over the entire surface, starting with the raised panel sections. Always make final brush strokes in the direction of the embossed grain.
Minwax® Gel Stain remains brushable for an extended period of time. Areas of heavier coats should be evened out before moving to a new section.
Gel Stain, while wet, is easily removed with a rag moistened with mineral spirits.
Allow stain to dry approximately 6 to 8 hours.
To darken the color, apply additional coats of Gel Stain by following the instructions above. Allow approximately 6 to 8 hours between coats for the stain to dry.

METAL DOORS DIRECTIONS:
SURFACE PREPARATION:

You will need: a graining tool, clean, dry, lint-free cloths, and clean, dry synthetic brushes. (Practice with the graining tool on a piece of scrap following the instructions in Step 3 until you feel comfortable using it)
Most metal doors come already primed, but usually not in the color you should be starting with.
Select an oil-based base coat tinted to match the light tone in the wood you're trying to create.
Apply a thin layer of the base coat paint to the entire door and allow it to dry thoroughly.
Then, mask all areas, such as glass, that you do not wish to stain and remove all hardware and doorknobs. Clean the surface with a cloth dampened with mineral spirits to remove all dust, grease and dirt.

STAIN APPLICATION:

Plan to work on the door in separate vertical and horizontal sections. Mask off the horizontal sections as you work on the vertical sections. The vertical sections need to be masked off when working on the horizontal sections. Each section must be completely dry before either removing or applying masking tape.
Select a Minwax® Gel Stain color that corresponds to the darkest color of the wood grain you are trying to create.
Test stain on hidden area to verify desired color.
Apply a thin, even coat of Gel Stain to a section using a natural bristle brush or a soft, lint-free cloth. Apply in the direction of the grain you intend to create.

GRAINING:

While the Gel Stain is wet, use a graining tool to create a wood grain pattern.
Apply downward pressure while moving the graining tool across the section at a constant speed. Use a long, steady, non-stop stroke -- rocking the tool one rotation as you move from beginning to end. Keep the graining tool clean by wiping it often with a rag or paper towel between strokes.
Repeat the above steps section by section.
If you are not satisfied with any given attempt, either wipe the surface clean or re-brush the area and start over again. Wet or tacky Gel Stain can be removed easily with a rag moistened with mineral spirits.
To complete the graining process, wait until the first coat of Minwax® Gel Stain is completely dry (24-48 hours), then apply a second coat of Gel Stain with a natural bristle brush in the direction of the grain pattern created. Work section by section as you did before. There is no need to mask off any sections.
While the Gel Stain is wet, use a clean, dry synthetic brush to remove the excess stain and create a uniform look. Use long brush strokes in the direction of the grain and remove the Gel Stain from the brush as it begins to accumulate with paper towels or a rag. The amount of Gel Stain left on will determine the depth of color.
Helpful Hints: On metal doors, use masking tape to mask off areas where sections meet. Let the section dry to the touch before working on a section next to it. This will ensure a clean, straight edge where panels meet.

CLEAR FINISH APPLICATION: (Fiberglass and Metal Doors)

Be sure to apply a protective clear finish such as Minwax® Fast Drying Polyurethane for interior use or Minwax® Helmsman® Spar Urethane for exterior applications.
Apply the oil-based protective clear finish using a natural bristle brush following the label directions. Remember to start with the raised panel sections and make final brush strokes in the direction of the embossed grain. Allow the finish to dry (at least 6 hours) before installing (or closing) the door to avoid sticking.
Do not apply a protective clear finish if the last coat of Minwax® Gel Stain can be removed with a rag moistened with mineral spirits.
Every 12-24 months, apply a coat of protective clear finish to keep the door looking beautiful.

Minwax® Water Based Wood Stain is a fast and easy way to add beautiful color to unfinished wood. It comes in 50 traditional wood tones and contemporary decorative colors. Minwax® Water Based Wood Stain is fast-drying, low odor, and can be easily cleaned up with soap and water. When used with Minwax® Water Based Pre-Stain Conditioner, it provides rich, beautiful color results.

* Minwax® Water Based Wood Stain colors are mixed at the paint counter of most home centers and hardware stores.

* Minwax® Water Based Wood Stain is not recommended for large surfaces, such as floors.

858ml Clear - Sku 27304-48, Model 61807, $16.99 each
946ml White Wash - Sku 27325-01, Model CM6186000, $17.49 each

Application tool: synthetic bristle brush, cloth or foam applicator
Location: interior wood surfaces
Dry time: 3 hours
Recoat: after 2 hours
Cleanup: soap and water
Coverage: 100 sq. ft. per quart
Coats: normally 1. Additional coats may be applied for richer color
Recommended uses: furniture, woodwork, cabinets, doors, accessories

White Wash Pickling Stain
Soft, subtle finish that adds just a wash of white color,
while allowing the wood grain to show through

FAQ:

Q. What is the advantage to using a water-based stain?
Water based stains have little odor, dry quickly and clean up with soap and water. Projects can often be completed in one day.

Q. Will Minwax® Water Based Wood Stain raise the grain of the wood?
As long as Minwax® Water Based Pre-Stain Wood Conditioner is used prior to staining, Water Based Wood Stain will not raise the wood grain.

Q. How long should Minwax® Water Based Wood Stain be left on wood?
Water-based stain dries very quickly. It should be allowed to penetrate no more than three minutes before wiping away the excess.

Q. Should Minwax® Water Based Wood Stain be used on floors?
No. Water-based stains dry very quickly, making them difficult to apply evenly over large surfaces. For very large areas such as floors, we recommend an oil-based product such as Minwax® Wood Finish™ Stain.

Q: What is a tint base?
Minwax® Water Based Wood Stain comes in two tint bases—Clear Tint Base and White Tint Base—that are used to make 50 different stain colors. A tint base is brought to the paint counter at the home center or hardware store for color mixing, similar to the way paint is mixed.

Q. What is White Wash Pickling Stain?
It is a Water Based Wood Stain that adds a subtle shade of white color to wood while allowing the natural grain to show through. Unlike the Clear and White Tint Bases, the White Wash Pickling Stain does not require mixing and is ready to use right out of the can.

Q: Which clear protective topcoat should be used over Minwax® Water Based Wood Stain?
We recommend Minwax® Polycrylic® Protective Finish for a crystal-clear topcoat that will not alter the appearance of the stain color. For a warmer, slightly amber finish over wood tones, Minwax® Water Based Oil-Modified Polyurethane is recommended.

DIRECTIONS:

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup.
SURFACE PREPARATION:

Sand the wood in the direction of the grain, first using medium-grade sandpaper (#120) working your way to fine-grade sandpaper (#220). Do Not Use Steel Wool. Remove all sanding dust.
Apply Minwax® Water Based Pre-Stain Wood Conditioner and allow to penetrate 1-5 minutes. This will help ensure even stain color penetration and reduce grain raising on soft and hard woods. Remove excess with a clean cloth.
For best results, wait 15-30 minutes before lightly sanding the surface with a fine-grade sandpaper. This will help smooth any raised grain. Remove all sanding dust.

STAIN APPLICATION:

Stir contents thoroughly before and during use.
Test stain on a hidden area to verify desired color.
When working with more than one can, we recommend mixing together the contents of the cans to ensure color consistency.
Apply stain with a synthetic bristle brush, foam brush, staining pad or rag. Allow stain to penetrate no longer than 3 minutes.
While stain is still wet, remove excess with clean cloth lightly dampened with stain. Wipe in the direction of the grain using light to medium pressure to achieve even stain color.
Note: Any uneven color penetration can be blended. Rewet the surface with more stain and lightly rub the stain into the surface, blending light and dark areas.
To increase color intensity, apply a second coat after 2 hours- repeating directions for application of first coat. Heavier application, lower temperature, and or higher humidity will extend drying time. Do not apply below 55°F.

Minwax® PolyShades® combines beautiful oil based wood stain and polyurethane in one simple step. Minwax® PolyShades® provides rich wood color and long lasting protection while enhancing the wood grain. PolyShades® will reduce finishing time compared with staining with one product and protecting with another.

Sheens: Satin and Gloss
Application tool: high-quality natural bristle brush
Location: interior wood surfaces
Dry time: 6 hours
Recoat: after 6 hours
Cleanup: mineral spirits
Coverage: 120-150 sq. ft. per quart
Coats: Normally 2. Additional coats may be applied for richer color.
Recommended uses: furniture, woodwork, doors, cabinets, accessories

The colors shown are for reference purposes only. They have been reproduced using digital production techniques. Always test stain on a hidden area of the wood to verify desired color.

FAQ:

Q. What is the advantage of PolyShades®?
PolyShades® combines stain for beautiful color with polyurethane for tough protection in one product. It is an ideal choice for those who want to save the time involved in staining with one product and protecting with another.

Q. Should Minwax® Pre-Stain Wood Conditioner be used as a pretreatment prior to PolyShades®?
Yes, if the wood being stained is soft or porous. Soft or porous woods, such as pine or aspen, tend to absorb stain unevenly. Before using PolyShades® on soft or porous woods, Pre-Stain Wood Conditioner should be applied to ensure even stain penetration.

Q. Can PolyShades® be applied over an existing finish?
Yes, as long as the previous finish is not lacquer or shellac. Be sure to test the selected color on a hidden spot to see how it will look over the original finish. To prepare the surface, make sure that the finish is clean and has had all wax and polish removed. Then lightly sand with #180 or #220 sandpaper. The surface is now ready to be coated with PolyShades®.

Q. Can Minwax® Fast-Drying Polyurethane or Wipe-On Poly be applied over PolyShades®?
Yes. Since PolyShades® contains polyurethane, additional protection, without added color, can be provided with a clear coat of Minwax® Fast-Drying Polyurethane or Wipe-On Poly over the last coat of PolyShades®.

Q. Can PolyShades® be used on floors?
PolyShades® is not recommended for use on floors. Instead, stain with Minwax® Wood Finish™ and topcoat with Minwax® Super Fast-Drying Polyurethane for Floors or Minwax® Fast-Drying Polyurethane.

DIRECTIONS:

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup.
SURFACE PREPARATION:

Sand raw wood smooth. Sand old finishes lightly to aid adhesion. Remove all sanding dust.
Surface must be dry and free from wax, grease, and dust. Do not use over paint, lacquer, shellac, polishes or products containing stearates.
Pre-treat raw soft or porous woods, such as pine and alder, with Minwax® Pre-Stain Wood Conditioner. This will help the wood absorb the stain color more evenly. Apply stain within two hours of pre-treatment.

STAIN APPLICATION:

Stir well before and occasionally during use.
Test stain on a hidden area to verify desired color.
Two coats are recommended for maximum beauty and protection.
Brush on a THIN, EVEN COAT in the direction of the grain. Be sure to maintain a wet edge.
Let dry 6 hours or more, then rub surface with fine steel wool (grade 000 and finer). Remove all dust.
Brush on a second THIN coat.
You may apply more than two coats if you want to deepen the color.

Minwax® Water Based WoodSheen® Rubbing Stain and Finish makes wood finishing fast and easy. This simple to use stain allows you to achieve beautiful color and a classic, hand-rubbed finish in minutes. And it's low odor, fast drying, and soap and water clean up. So easy to use, it's practically effortless. Just apply, wipe away the excess, let dry, and you're done.

Natural - Sku 76032-10, Model CM3040500, $10.99 each
Rosewood - Sku 76031-86, Model CM3045100, $10.99 each
Colonial Walnut - Sku 76031-94, Model CM3044300, $10.99 each
Plantation Walnut - Sku 76032-02, Model CM3043800, $10.99 each
Windsor Oak - Sku 76032-44, Model CM3041900, $10.99 each
Manor Oak - Sku 76032-28, Model CM3041400, $10.99 each

Application tool: cloth
Location: interior wood surfaces
Dry time: 1 hour
Recoat: after 1 hour
Cleanup: soap and water
Coverage: 60-65 sq. ft. per bottle
Coats: normally 2. Additional coats may be applied for richer color
Recommended uses: furniture, accessories, doors

The colors shown are for reference purposes only. They have been reproduced using digital production techniques. Always test stain on a hidden area of the wood to verify desired color.

FAQ:

Q. What are the advantages to using Minwax® Water Based WoodSheen® instead of a separate stain and clear finish?
With Minwax® Water Based WoodSheen®, you can complete a project far faster than with a standard stain and clear finish. Minwax® Water Based WoodSheen®dries in just an hour. It's also extremely easy to use. Apply it, wipe away the excess, and you're done. It's low odor, and cleans up easily with soap and water.

Q. How many colors is Minwax® Water Based WoodSheen® available in?
Minwax® Water Based WoodSheen® is available in six colors.

Q. If I want extra durability, can I apply a clear topcoat over Minwax® Water Based WoodSheen®?
Yes. For extra durability without added color, wait three hours after applying Minwax® Water Based WoodSheen®, and then apply Minwax® Polycrylic®, Minwax® Water Based Polyurethane, or Minwax® Water Based Wipe-On Poly.

Q. How do I apply Minwax® Water Based WoodSheen®?
Minwax® Water Based WoodSheen® is very easy to use. Apply the product to bare wood. Wipe it onto the wood with a clean cloth, moving in the direction of the wood's grain. Wipe away any excess, again moving in the direction of the wood's grain. And that's it; you're done.

DIRECTIONS:

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup.

SURFACE PREPARATION:

Sand the wood smooth.
Remove all sanding dust.

Fast drying clear finish oil based protective offers exceptionally long lasting beauty. Seals, enhances, protects on all interior wood surfaces such as furniture, cabinets, doors and floors. Clean up with mineral spirits. Aerosol. 326g

Minwax® Fast-Drying Polyurethane is a clear, hard finish that dries fast to protect and beautify interior wood surfaces such as furniture, cabinets, moldings, and doors. Minwax® Fast-Drying Polyurethane Finish is among the most durable coatings for wood protection. Minwax®Fast-Drying Polyurethane's long-lasting protective finish makes it ideal for use on both finished and unfinished wood.

* Fast-Drying Polyurethane is also available in can format (see listing below)

Gloss - Sku 27336-73, Model 33050, $9.79 each
Semi-Gloss - Sku 27336-65, Model 33055, $9.79 each
Satin - Sku 27336-57, Model 33060, $9.79 each

Sheens: Gloss, Semi-Gloss, Satin
Application tool: natural bristle brush, foam brush, or lambswool applicator
Location: interior wood surfaces
Recoat: after 4-6 hours
Cleanup: mineral spirits or paint thinner
Coverage: 125 sq. ft. per quart
Coats: 2-3
Recommended uses: woodwork, furniture, doors, cabinets and floors

FAQ:

Q. What is the best way to select a sheen?
Sheen choice is a personal preference. Satin sheens reflect less light and gloss sheens reflect more light.

Q. Is one sheen more durable than the others?
No. The additives that distinguish satin from semi-gloss and gloss do not compromise the durability of the finish.

Q. What can be done to avoid bubbles in the finish?
There are four ways. First, stir, don't shake, the can. Second, use a high-quality, natural bristle brush. Third, work the finish into the wood, but don't create excess foam. Fourth, "tip-off" the finish before stopping, carefully running the brush at a 45-degree angle the length of each board in one unbroken movement. This will burst and smooth out any bubbles that may have been created.

Q. Should Minwax® Fast-Drying Polyurethane be sanded between coats?
Yes. A light sanding (#220 sandpaper) will remove any fine particles of dust that have settled on the finish while it was still wet. Light sanding also helps abrade the surface, improving intercoat adhesion.

Q. Why does Minwax® Fast-Drying Polyurethane sometimes take longer to dry than the instructions indicate?
The drying time is affected by the amount of moisture in the air, the air temperature and the thickness of the coats. When humidity is high, temperature is low, or coats are thick, it takes longer for the film to dry.

Q. What is the best way to determine how many coats of Minwax® Fast-Drying Polyurethane to apply?
If you look closely at the wood in bright, direct light, you should not be able to detect any dry spots. If you do, an additional coat is necessary to protect the wood.

Q. Does Minwax® Fast-Drying Polyurethane need to be waxed?
No. Wax does provide an extra layer of protection, but it will prevent you from applying an additional coat of Minwax® Fast-Drying Polyurethane in the future without first removing the wax. Instead, we recommend using Minwax® Wood Cleaner to keep wood clean and looking beautiful.

DIRECTIONS:

Minwax® Fast-Drying Polyurethane is a clear, hard finish that dries fast to protect and beautify interior wood surfaces such as furniture, cabinets, moldings, and doors. Minwax® Fast-Drying Polyurethane Finish is among the most durable coatings for wood protection. Minwax®Fast-Drying Polyurethane's long-lasting protective finish makes it ideal for use on both finished and unfinished wood.

* Fast-Drying Polyurethane is also available in an aerosol can (see listing above).

Sheens: Gloss, Semi-Gloss, Satin
Application tool: natural bristle brush, foam brush, or lambswool applicator
Location: interior wood surfaces
Recoat: after 4-6 hours
Cleanup: mineral spirits or paint thinner
Coverage: 125 sq. ft. per quart
Coats: 2-3
Recommended uses: woodwork, furniture, doors, cabinets and floors

FAQ:

Q. What is the best way to select a sheen?
Sheen choice is a personal preference. Satin sheens reflect less light and gloss sheens reflect more light.

Q. Is one sheen more durable than the others?
No. The additives that distinguish satin from semi-gloss and gloss do not compromise the durability of the finish.

Q. What can be done to avoid bubbles in the finish?
There are four ways. First, stir, don't shake, the can. Second, use a high-quality, natural bristle brush. Third, work the finish into the wood, but don't create excess foam. Fourth, "tip-off" the finish before stopping, carefully running the brush at a 45-degree angle the length of each board in one unbroken movement. This will burst and smooth out any bubbles that may have been created.

Q. Should Minwax® Fast-Drying Polyurethane be sanded between coats?
Yes. A light sanding (#220 sandpaper) will remove any fine particles of dust that have settled on the finish while it was still wet. Light sanding also helps abrade the surface, improving intercoat adhesion.

Q. Why does Minwax® Fast-Drying Polyurethane sometimes take longer to dry than the instructions indicate?
The drying time is affected by the amount of moisture in the air, the air temperature and the thickness of the coats. When humidity is high, temperature is low, or coats are thick, it takes longer for the film to dry.

Q. What is the best way to determine how many coats of Minwax® Fast-Drying Polyurethane to apply?
If you look closely at the wood in bright, direct light, you should not be able to detect any dry spots. If you do, an additional coat is necessary to protect the wood.

Q. Does Minwax® Fast-Drying Polyurethane need to be waxed?
No. Wax does provide an extra layer of protection, but it will prevent you from applying an additional coat of Minwax® Fast-Drying Polyurethane in the future without first removing the wax. Instead, we recommend using Minwax® Wood Cleaner to keep wood clean and looking beautiful.

DIRECTIONS:

Minwax® Wipe-On Poly is a durable, clear polyurethane that provides protection with classic, hand-rubbed beauty. Minwax® Wipe-On Poly is applied with a cloth that avoids drips and brush marks. Minwax Wipe-On Poly is the perfect oil based clear protective finish for your interior wood.

Clear Gloss - Sku 27339-05, Model 39003, $20.99 each
Clear Satin - Sku 27339-13, Model 33103, $20.99 each

Sheens: Gloss, Satin
Application tool: lint-free cloth
Location: interior wood surfaces
Recoat: after 2-3 hours
Dry time: 24 hours
Cleanup: mineral spirits or paint thinner
Coverage: 125 sq. ft. per quart
Coats: 2-3
Recommended uses: furniture, cabinets, woodwork, trim, doors; small floor touch-ups (scratches)

FAQ:

Q. What is the benefit of using Minwax® Wipe-On Poly versus a traditional polyurethane?
Minwax® Wipe-On Poly is easily applied with a cloth, without any drips or brush marks. It is the perfect choice for furniture, interior doors, trim and other woodwork.

Q. Can Minwax® Wipe-On Poly be used on floors?
Minwax® Wipe-On Poly provides a durable layer of topcoat protection but it is thinner than regular polyurethanes. It can be used on floors to touch up small areas that are worn or scratched. For new floors or floors that need to be refinished, Minwax® Fast-Drying Polyurethane or Minwax® Super Fast-Drying Polyurethane for Floors should be used.

Q. How is Minwax® Wipe-On Poly applied?
Minwax® Wipe-On Poly is easily applied by hand, using a soft, lint-free cloth. Put a liberal amount on a clean cloth and rub into the wood. Since it is applied with a cloth, there is no need to worry about drips or brush marks.

Q. Can Minwax® Wipe-On Poly be applied over Minwax® Wood Finish™ or other stains?
Yes. Minwax® Wipe-On Poly is a great way to protect finished or unfinished wood. Be sure to allow wood that has been stained to dry completely before topcoating with Minwax® Wipe-On Poly.

Q. Should Minwax® Wipe-On Poly be sanded between coats?
Yes. A light sanding with very fine sandpaper (#220) or fine steel wool will remove any fine particles of dust that may have settled on the finish while it was wet. Allow Minwax® Wipe-On Poly to dry 2-3 hours before applying the next coat. If a third coat is desired, repeat the same procedure.

DIRECTIONS

A clear, fast-drying finish that combines superior durability with the warmth and beauty of traditional polyurethane. It is waterbased, therefore it has little odor and cleans up easily with warm water. It protects and adds beauty to interior wood surfaces such as furniture, cabinets, floors and doors.

* Water Based Oil-Modified Polyurethane is also available in an aerosol can.

Sheens: Gloss, Semi-Gloss, Satin
Application tool: synthetic bristle brush, foam brush, or lambswool applicator
Location: interior wood surfaces
Recoat: after 2 hours
Dry Time: 24 hours
Cleanup: warm water
Coverage: 125 square feet per quart
Coats: 3
Recommended uses: furniture, cabinets, floors and doors
VOC content: maximum VOC of 275 g/L

FAQ:

Q: What is Minwax® Water Based Oil-Modified Polyurethane?
Water Based Oil-Modified Polyurethane is a clear, ultra fast-drying finish that combines superior durability with the warmth and beauty of traditional polyurethane. Because it's water-based, it has little odor and cleans up easily with warm water.

Q: Where can I use Water Based Oil-Modified Polyurethane?
Water Based Oil-Modified Polyurethane is ideal for use on all interior bare or stained wood surfaces including furniture, cabinets, doors and floors. It can be applied over oil-based stains like Minwax® Wood Finish™ or Minwax® Gel Stain. It also can be applied over Minwax® Water Based Wood Stain wood tones, provided the stain has dried completely.

Q: How many coats do I need to apply?
Three coats are recommended.

Q: Can I mix Minwax® Water Based Oil-Modified Polyurethane with Minwax® Fast-Drying Polyurethane?
No. The oil-based and water-based products are not compatible and they should not be mixed together. However, the results are the same—a beautiful, durable finish!

Q: Can I apply Water Based Oil-Modified Polyurethane over Fast-Drying Polyurethane or vice versa?
Yes. The two products can be applied over each other as long as the first has fully cured. Follow the directions for the product you are using. Be sure to apply each coat with only one product. Do not finish part of a surface with one topcoat and part with the other as this could result in a uneven appearance across the surface of the wood.

Q: What is the V.O.C. level of Water Based Oil-Modified Polyurethane?
Water Based Polyurethane has a maximum V.O.C. of 275 g/L.

DIRECTIONS:

Minwax® Polycrylic® Protective Finish is a crystal clear, fast-drying protective topcoat for use over bare wood, oil- and water-based stains, paint and wallpaper. It has very little odor, is non-flammable, cleans up easily with soap and water, and can be recoated in only 2 hours. Minwax® Polycrylic® resists damage from abrasion, scuffing, chipping, water, alcohol and other common household chemicals.

Minwax® Polycrylic® is not recommended for use on floors.

* Minwax® Polycrylic® is also available in an aerosol can.

Sheens: Gloss, Semi-Gloss, Satin
Application tool: synthetic bristle brush
Location: interior wood surfaces
Dry time: 2 hours
Recoat: after 2 hours
Cleanup: warm water
Coverage: 125 sq. ft. per quart
Coats: 2-3
Recommended uses: woodwork, cabinets, furniture, interior doors, accessories
VOC content: maximum VOC of 275 g/L

FAQ:

Helmsman® Spar Urethane is a specially formulated protective clear finish for exterior or interior wood that is exposed to sunlight, water, or temperature changes. It contains UV blockers to reduce the sun's graying and fading effects. Helmsman® Spar Urethane forms a protective barrier against rain and moisture and its special oils allow the finish to expand and contract with the wood as seasons and temperatures change.

Helmsman® Spar Urethane is not recommended for use on floors.

* Helmsman® Spar Urethane is also available in an aerosol can.

Sheens: Gloss, Semi-Gloss, Satin
Application tool: natural bristle brush
Location: interior and exterior wood surfaces
Recoat: after 4 hours
Dry time: 24 hours
Cleanup: mineral spirits
Coverage: 125 sq. ft. per quart
Coats: 2-3
Recommended uses: doors, windows, bathroom cabinets, bar tops, kitchen countertops and outdoor furniture

Water Based Helmsman® Spar Urethane is a crystal clear, waterbased finish that is specially formulated to protect wood against nature's toughest conditions. Water Based Helmsman®forms a protective barrier against rain and moisture and the ultraviolet absorbers found in Water Based Helmsman® reduce the graying and fading effects of the sun. Because it's water-based, it has little odor and cleans up easily with warm water.

Water Based Helmsman® Spar Urethane is not recommended for use on floors.

Satin Finish - Sku 76093-16, Model CM7105200, $54.99 each
Semi-Gloss Finish - Sku 76093-08, Model CM7105100, $54.99 each
Gloss Finish - Sku 76092-90, Model CM7105000, $54.99 each

Sheens: Gloss, Semi-Gloss, Satin
Application tool: synthetic bristle brush
Location: interior and exterior wood surfaces
Recoat: after 2 hours
Dry time: 24 hours
Cleanup: warm water
Coverage: 125 sq. ft. per quart
Coats: 3-4
Recommended uses: doors, windows, bathroom cabinets, bar tops, kitchen countertops and outdoor furniture
VOC content: Maximum VOC of 275 g/L

Minwax® Water Based Polyurethane for Floors Base Coat dries quickly to provide an outstanding clear base coat for Minwax® Water Based Polyurethane for Floors. Minwax® Water-Based Polyurethane for Floors Base Coat seals the wood grain, preventing discoloration (tannin reaction) between the wood and Minwax® Water Based Polyurethane for Floors. Many water based finishes have a high pH level that can react with bare wood causing it to discolor.

Sku 75601-96, Model CM1765000, $52.99 each

Application tool: synthetic pad applicator
Location: interior wood floors
Dry time: 2 hours
Cleanup: warm water
Coverage: 400-500 square feet per gallon
Coats: 1
Recommended uses: hardwood floors - use with Minwax® Water Based Polyurethane for Floors
Note: If floor is going to be stained, Water Based Polyurethane Base Coat is not required. Apply Water Based Polyurethane for Floors directly over stain.

Minwax® Water Based Polyurethane for Floors is a durable protective finish specifically formulated for hardwood floors.  Minwax® Water Based Polyurethane for Floors is water-based, therefore has little odor, dries quickly and cleans up with warm water.  Most projects can be completed in one day!

Satin - Sku 75602-04, Model CM1666600, $64.99 each
Semi Gloss - Sku 75602-12, Model CM1777700, $64.99 each
Gloss - Sku 75602-20, Model CM1888800, $64.99 each

Sheens: Gloss, Semi-Gloss, Satin
Application tool: lambswool or synthetic pad applicator, or a natural bristle brush
Location: interior wood floors
Recoat: at least 2 hours
Dry Time: 24 hours
Clean up: warm water
Coverage: 500-600 square feet per gallon
Coats: 3
Recommended uses: hardwood floors
VOC content: maximum VOC of 250 g/L

Finishing a new floor or refinishing an old floor? Minwax® Super Fast-Drying Polyurethane for Floors is a durable, protective finish specifically formulated for use on hardwood floors. Minwax® Super Fast-Drying Polyurethane for Floors has a 25% faster recoat time than regular polyurethanes and does not require sanding between coats. Its professional anti-settling formula levels to a smooth, even sheen. A hardwood floor topcoating project can be completed in just one day!

Gloss - Sku 76091-91, Model CM1302700, $54.99 each
Semi-Gloss, pack of 2 - Sku 75663-42, model CM1302300, $94.99/pack
Satin - Sku 74008-56, Model CM13022000, $54.99 each

Sheens: Gloss, Semi-Gloss, Satin
Application tool: lambswool or synthetic pad applicator, or a natural bristle brush
Location: interior wood floors
Recoat: after 3-4 hours
Dry time: 12-18 hours
Cleanup: mineral spirits or paint thinner
Coverage: 600-700 sq. ft. per gallon
Coats: 2-3
Recommended uses: hardwood floors

Minwax® High Performance Wood Hardener is a quick-drying liquid formulated to strengthen and reinforce decayed or rotting wood. Minwax®High Performance Wood is made up of solvents that carry resin deep into the pores of the wood where they evaporate and leave behind hardened resin resulting in hardened wood.

Sku 27360-72, Model 41700, $13.99 each

Application tool: disposable bristle brush
Dry time: 2-4 hours, then fill with Minwax® High Performance Wood Filler
Cleanup: acetone, following manufacturer's safety instructions
Recommended uses: windowsills, doors, woodwork, floors, decks, furniture, woodwork

#1 Natural Pine - Sku 27330-12, Model 10101, $4.49 each Buy Now!
#2 Bleached - Sku 27330-46, Model 10201, $4.49 each Buy Now!
#3 Natural Birch - Sku 27330-53, Model 10301, $4.49 each Buy Now!
#4 Frosted Colour - Sku 27330-61, Model 10401, $4.49 each Buy Now!
#5 Colonial Maple - Sku 27330-87, Model 10501, $4.49 each Buy Now!
#6 American Walnut - Sku 27331-11, Model 10601, $4.49 each Buy Now!
#7 Mahogany Cherry - Sku 27331-29, Model 10701, $4.49 each Buy Now!
#8 Ebony/Dark Walnut - Sku 27331-37, Model 10801, $4.49 each Buy Now!

DIRECTIONS:

Minwax® Wood Finish™ Stain Markers contain oil-based stains that enable touchups and repair of furniture, cabinets, doors and floors. Minwax® Wood Finish™ Stain Markers are also used to stain and detail small hobby and woodcraft projects. Whether you need to repair your wood or stain and detail your small wood projects, Minwax oil-based stain markers make the job easy.

Golden Oak - Sku 27364-03, Model 23481, $9.99 each Buy Now!
Provincial - Sku 27364-11, Model 23482, $9.99 each Buy Now!
Red Oak - Sku 27364-29, Model 23483, $9.99 each Buy Now!
Red Mahogany - Sku 27364-37, Model 23484, $9.99 each Buy Now!
Early American - Sku 27364-45, Model 23485, $9.99 each Buy Now!
Cherry - Sku 27364-52, Model 23486, $9.99 each Buy Now!
Dark Walnut - Sku 27364-60, Model 23487, $9.99 each Buy Now!

Application tool: marker-type dispenser
Dry time: ready for immediate use
Cleanup: mineral spirits or paint thinner following manufacturer's safety instructions
Recommended uses: furniture, kitchen cabinets, doors, molding, interior wood surface

The colors shown are for reference purposes only. They have been reproduced using digital production techniques. Always test stain on a hidden area of the wood to verify desired color.

DIRECTIONS:

Minwax® Wood Putty® is a non-hardening, pre-mixed putty that repairs small holes and covers other minor imperfections in bare, painted, stained, and finished wood. Minwax® Wood Putty® is color-matched to Minwax® Wood Finish™ stains to make your wood repairs easier.

Natural Pine - Sku 27363-04, Model 13610, $4.99 each
Golden Oak - Sku 27363-12, Model 13611, $4.99 each
Colonial Maple - Sku 27363-20, Model 13612, $4.99 each
Mahogany - Sku 27363-38, Model 13613, $4.99 each
Colonial Walnut - Sku 27363-46, Model 13614, $4.99 each
Cherry - Sku 27363-53, Model 13615, $4.99 each
White - Sku 27363-61, Model 13616, $4.99 each
Walnut - Sku 27363-79, Model 13617, $4.99 each
Ebony - Sku 27363-87, Model 13618, $4.99 each
White Oak - Sku 27363-95, Model 13619, $4.99 each

Application tool: putty knife
Surface Preparation: no sanding necessary
Cleanup: soap and water
Recommended uses: bare, stained or finished woodwork, paneling, molding, trim and doors

Minwax® Wood Putty is color-matched to Minwax® Wood Finish™ stains and is available in 10 colors.

Minwax® High Performance Wood Filler is used to fill gouges and holes in split, damaged or rotted exterior or interior woods. It is weather, water, and rot resistant. Minwax® High Performance Wood Filler is also effective as a wood adhesive where you can anchor screws and secure loose joints in furniture. It strongly bonds to wood as well as almost any rigid surface including ceramics, concrete, metal, and fiberglass. Minwax High Performance Wood Filler is the perfect product for your wood repairs.

Sku 27360-64, Model 11002, $16.99 each

Application tool: narrow putty knife
Preparation: prior to use, strengthen and reinforce decayed or rotting wood using Minwax® High Performance Wood Hardener.
Sand: after 30 minutes
Cleanup: acetone following manufacturer's safety instructions
Recommended uses: windowsills, doors, woodwork, floors, decks, furniture

Minwax® Stainable Wood Filler is ideal for repairing cracks, gouges, nail holes, knot holes and other defects in all types of unfinished indoor and outdoor wood surfaces.

It is specially formulated to accept Minwax® penetrating wood stains, including Minwax® Wood Finish, Minwax® Gel Stain and Minwax® Water Based Wood Stain.

Minwax® Stainable Wood Filler is a latex based, quick drying, sandable wood filler and easy to clean with soap & water.

29ml - Sku 72869-09, Model 528510000, $5.29 each
177ml - Sku 72869-66, Model 528520000, $7.79 each
473ml - Sku 72869-74, Model 528530000, $11.49 each

Application tool: putty knife
Dry time: 2-6 hours, depending on size of area filled
Stain Application: as soon as wood filler has dried
Cleanup: soap and water
Recommended uses: for filling cracks, gouges, nail holes, knot holes and other defects in unfinished wood

Minwax® Wood Cleaner can be used to clean all unwaxed interior wood surfaces in the home that are coated with a clear finish. Great as a quick and easy cleaner for cabinets, furniture, doors, paneling, painted wood and trim. Minwax® Wood Cleaner is not for use on waxed, oiled or unfinished wood or wood finished with shellac.

Sku 27020-58, Model 67107, $8.29 each

Application tool: cloth or mop
Coverage: 2400 sq. ft. per quart
Usage frequency: as often as necessary
Recommended uses: wood surfaces with a clear, unwaxed finish

Minwax® Hardwood Floor Reviver refreshes hardwood floors that are worn, scratched, or dull. It is available in both High-Gloss and Low-Gloss sheens. Applying Hardwood Floor Reviver requires no sanding or special preparation, just squirt onto floor, spread with application tool and let dry. Provides, care, beauty and protection for your hardwood floors for 3-6 months.

High Gloss - Sku 74628-56, Model CM6095000, $27.99 each
High Gloss with Bonus Cleaner - Sku 75671-75, Model CM6099000, $27.99/pack
Low Gloss - Sku 74628-80, Model CM6096000, $27.99 each
Low Gloss with Bonus Cleaner - Sku 75671-83, Model CM6098000, $27.99/pack

Sheens: High-Gloss, Low-Gloss
Application tool: painter's pad or synthetic applicator attached to a long handle
Dry Time: 2 hours
Coverage: approximately 175-225 sq. ft. per quart
Recommended uses: interior hardwood floors
VOC content: maximum VOC of 275 g/L

FAQ:

Q. What is Minwax® Hardwood Floor Reviver
Stronger and more durable than polish, Reviver is a topcoat that restores shine and provides a layer of protection to any unwaxed, polyurethane-finished floor. Reviver quickly and easily renews the beauty of hardwood floors that are dull, scratched, scuffed or showing signs of wear.

Q. How can I tell if my floor has wax on it?
Apply a few drops of water to the floor. Wait 10 minutes. If the wetted area turns white, the floor may have a wax coating. Do not proceed with the application of Reviver.

Q. Can Reviver be used on pre-finished hardwood floors?
No. Reviver will not adhere to pre-finished flooring. If you are unsure if your floor is pre-finished, test Reviver on an inconspicuous area.

Q. Can Reviver be used on floors that are in very poor condition?
No. Badly damaged floors or floors that have large areas where the finish is worn away will require a complete refinishing.

Q. How do I prepare the floor before I apply Reviver?
There is no sanding or special preparation required. Simply sweep or vacuum the floor to remove all loose dirt. Then, wash the floor with a mild oil-free cleaner such as Minwax® Hardwood Floor Cleaner and allow to dry.

Q. Does Reviver need to be mixed with water?
No. Reviver is premixed and ready to use.

Q. How do I apply Reviver?
Squirt Reviver lightly in an "S" pattern directly onto the floor working one area at a time. Then spread the Reviver with a painter's pad in the direction of the grain and let dry.

Q. Will Reviver change the color of my floor?
No. Reviver is non-ambering. It dries quickly to a crystal clear finish.

Q. How often can I use Reviver?
Reviver can be reapplied every 3-6 months as needed.

Q. Is Reviver an oil- or water-based product?
Reviver is water-based. It is low odor, dries quickly and application tools can be cleaned with soap and water.

DIRECTIONS:

PREPARE THE FLOOR:

Sweep or vacuum the floor to remove all loose dirt
Wash the floor with a mild oil-free cleaner such as Minwax® Hardwood Floor Cleaner
Allow to dry completely
Test Minwax® Hardwood Floor Reviver on a small inconspicuous area of the floor such as inside a closet to ensure adhesion and compatibility. Wax and other ingredients in some floor polishes may cause Reviver to bead up or prevent it from adhering to the floor
Note: Minwax® Hardwood Floor Reviver is not recommended for use over unfinished, newly finished, waxed or oiled floors. To test for wax, apply a few drops of water to the floor. Wait 10 minutes. If the wetted area turns white, the floor may have a wax coating. Reviver is not designed for use on floors that are in very poor condition. Badly damaged floors or floors that have large areas where the finish is worn away will require a complete refinishing.

APPLY THE COATING:

Rock the bottle several times before opening the cap. Do not shake.
Squirt Minwax® Hardwood Floor Reviver lightly in an "S" pattern directly onto the floor in a 3 x 3 foot area using a damp painter's pad or synthetic applicator attached to a long handle, spread Reviver across the floor.
Work in the direction of the grain using a back-and-forth motion. Keep working in small sections until the entire floor is coated. For best results, apply a thin, even coat. Keep airborne dust to a minimum while the floor is wet.

Gently cleans to maintain the natural beauty wood. Without leaving any residue. Solvent-free. Minimizes water contact. Great for unwaxed finishes. Regular use will keep hardwood floors looking beautify by gently removing dirt and grime without leaving a soap film behind. 946ml

HardwWood Floor Cleaner is specially formulated to help maintain the natural beauty of hardwood and laminate floors. Minwax®Wood Cleaner is not for use on waxed, oiled or unfinished wood or wood finished with shellac. Safely remove dirt, grease, and grime from hardwood and laminate floors without leaving any residue.

Sku 27020-41, Model 67003, $8.29 each

Application tool: cloth or mop
Usage frequency: as often as necessary
Recommended uses: hardwood floors, laminates, and pre-finished flooring

Minwax® Pre-Stain Wood Conditioner penetrates the grain of the wood to promote uniform acceptance of wood stain. Minwax®Pre-Stain Wood Conditioner helps prevent streaking and blotching to help ensure a beautiful, even stain. It is specifically designed to condition wood before staining new or bare softwood surfaces

236ml - Sku 27329-72, Model 27329-72, $7.79 each
946ml - Sku 27329-80, Model 20003, $15.49 each
3.78L - Sku 27329-98, Model 20099, $42.99 each

Application tool: cloth or brush
Dry time: 15 minutes
Stain Application: after 15 minutes, but no more than 2 hours
Cleanup: mineral spirits or paint thinner, following manufacturer’s safety instructions
Coverage: 125 sq. ft. per quart
Coats: normally 1, but additional coats may be applied on highly absorbent woods
Recommended uses: any soft or porous woods - common examples include pine, fir and spruce (soft) or maple, alder and aspen (porous)

FAQ:

Q. What is the purpose of Minwax® Pre-Stain Wood Conditioner?
Much of the wood used for projects is "soft" wood, such as pine or spruce. Some hardwoods, such as alder or aspen, are porous and tend to absorb stain unevenly. To help ensure even stain color penetration and beautiful results, it is essential to pre-treat soft or porous woods with Minwax® Pre-Stain Wood Conditioner.

Q. How does Minwax® Pre-Stain Wood Conditioner work?
Minwax® Pre-Stain Wood Conditioner penetrates the pores of the wood, reducing the amount of stain the larger pores will absorb. This evens out the absorption of stain, preventing streaking and blotching.

Q. Can Minwax® Pre-Stain Wood Conditioner be used on hardwoods such as oak or mahogany?
Yes, but more dramatic results will be seen on softwoods. Hardwoods tend to have a more uniform pore structure than softwoods, resulting in more uniform staining. Exceptions include maple, alder and aspen, which have uneven pore structures. Pre-Stain Wood Conditioner should be used on these woods.

Q. What happens to Minwax® Pre-Stain Wood Conditioner after two hours have elapsed?
The resins in Minwax® Pre-Stain Wood Conditioner will begin to dry and may inhibit stain absorption. To open the pores again, sand the wood lightly with a medium grit (#120 - #180) sandpaper.

Q. Does Minwax® Pre-Stain Wood Conditioner need to be sanded before stain is applied?
No. Minwax® Pre-Stain Wood Conditioner is not a sanding sealer and does not require this extra step as long as the stain is applied within 2 hours after pretreatment.

Q. Is it possible to apply too much Minwax® Pre-Stain Wood Conditioner?
No, not if label instructions are followed and any excess Minwax® Pre-Stain Wood Conditioner is wiped off after 5 - 15 minutes.

Q. Can Minwax® Pre-Stain Wood Conditioner be used prior to applying a water-based stain?
No. Since Minwax® Pre-Stain Wood Conditioner is an oil-based product, it should only be used as a pre-stain treatment with oil-based stains such as Minwax® Wood Finish™ stains. For water-based stains, use Minwax® Water Based Pre-Stain Wood Conditioner.

DIRECTIONS:

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup.

Apply before staining on clean, raw wood, using a brush or cloth.
Allow to penetrate for 5 to 15 minutes, then remove excess with clean, dry cloth.
The stain should be applied within two hours of application of Minwax® Pre-Stain Wood Conditioner. For best results, stain with Minwax® Wood Finish™, Minwax® Gel Stain, Minwax® PolyShades®.

Minwax® Water Based Pre-Stain Wood Conditioner penetrates the grain of the wood to promote uniform acceptance of Water Based Wood Stains and helps control the effect of grain raising on both soft and hard woods. Minwax® Pre-Stain Wood Conditioner helps prevent streaking and blotching to help ensure a beautiful, even stain. It is specifically designed to condition wood before staining new or bare wood surfaces.

236ml - Sku 27323-03, Model 31850, $6.99 each
946ml - Sku 27323-11, Model CM6185000, $15.99 each

Application tool: cloth, synthetic bristle brush or foam applicator
Dry time: 1-5 minutes
Stain Application: after allowing 15-30 minutes to dry and lightly sanding with fine grade sand paper
Cleanup: soap and water
Coverage: 100-125 square feet per quart
Coats: 1
Recommended uses: all soft or hard woods before using Water Based Wood Stains

Minwax® Antique Oil Finish is an oil-based protective finish that gives wood a soft, hand-rubbed lustre. It is durable, easily maintained, and highly resistant to staining. Minwax®Antique Oil Finish may be used over finished and unfinished wood.

Sku 27338-48, Model 70003, $19.49 each

Application tool: cloth or brush
Dry time: 5-10 minutes prior to buffing
Recoat: after 24 hours
Cleanup: mineral spirits or paint thinner following manufacturer's safety instructions
Coverage: 125-150 square feet per quart
Coats: 2 or 3
Recommended uses: furniture, antiques, woodwork, cabinets, doors, paneling, accessories

Minwax® Tung Oil Finish is an oil-based protective finish that also gives wood a hand-rubbed lustre. Minwax® Tung Oil Finish penetrates wood pores and restores vitality to dry, thirsty wood. Minwax® Tung Oil is easy to maintain and can be applied over stained and unstained wood. Give your wood the care and protection it deserves with an application of MinwaxMinwax® Tung Oil Finish.

Sku 27346-55, Model 78003, $18.49 each

Application tool: cloth or brush
Dry time: 5-10 minutes prior to buffing
Recoat: after 24 hours
Cleanup: mineral spirits or paint thinner following manufacturer’s safety instructions
Coverage: 125-150 sq. ft. per quart
Coats: 2 or 3
Recommended uses: furniture, antiques, woodwork, cabinets, doors, paneling, accessories

Minwax® Teak Oil protects dense woods and enhances wood grain by penetrating into wood pores, restoring the wood’s natural warmth and richness. Teak oil is recommended for outdoor and indoor furniture, and on marine surfaces above the water line. Use Minwax® Teak Oil periodically to refresh your dense woods and help protect them from moisture and UV rays.

Sku 76025-84, Model CM6710000, $19.99 each

Application tool: brush or cloth
Dry time: 6-8 hours
Cleanup: mineral spirits or paint thinner according to manufacturer’s safety recommendations
Coverage: 125-150 sq. ft. per quart
Coats: 1-2
Recommended uses: indoor and outdoor furniture and wood surfaces above the water line
* Not for use on outdoor decks, below waterline wood surfaces, and interior floors.

FAQ:

Q. What surfaces is Minwax® Teak Oil recommended for?
Minwax® Teak Oil is great for indoor and outdoor furniture made from hardwoods and on marine wood surfaces above the waterline.

Q. Can I apply Minwax® Teak Oil to wood floors or outdoor decks?
No. Minwax® Teak Oil is not recommended for wood floors or outdoor decks. Minwax® Teak Oil protects dense woods from moisture and UV rays by penetrating into the wood pores. Minwax® Teak Oil does not create a protective film on wood surfaces such as Minwax® Fast-Drying Polyurethane which is recommended for wood floors. For outdoor decks try Thompson's® Water Seal®.

Q. Does Minwax®Teak Oil contain UV inhibitors?
Minwax® Teak Oil does contain UV protection to delay the sun from graying the wood over time.

Q. How do I apply Minwax® Teak Oil?
Minwax® Teak Oil can be applied with a clean cloth or a brush. Apply Minwax® Teak Oil to bare wood or to wood that is free of old finishes, then wipe off any excess moving in the direction of the wood’s grain.

Q. Should Minwax® Teak Oil be applied repeatedly?
Yes. Minwax® Teak Oil should be reapplied whenever the wood appears to be dry or worn out in order to restore the effectiveness of the finish.

Q. Can I apply a topcoat over Minwax® Teak Oil?
Yes, a topcoat such as Minwax® Helmsman® Spar Urethane can be applied over Minwax® Teak Oil. Although we recommend that Minwax® Teak Oil be reapplied to dry, worn out wood, a topcoat such as Minwax® Helmsman® Spar Urethane will offer additional protection. Wait a minimum of 72 hours after applying Minwax® Teak Oil before applying additional topcoats.

DIRECTIONS:

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

SURFACE PREPARATION:

Surface must be dry and free of old finishes such as varnish, paint, polish, wax, grease, dirt, and subsurface moisture.
If desired, sand to obtain smooth, uniform surface.

APPLICATION:

Lightly shake container for 15 – 20 seconds.
Brush or wipe on a generous amount of Minwax® Teak Oil.
Allow Minwax® Teak Oil to penetrate into wood for 5 – 10 minutes. Do not wipe off any excess.
Apply a second coat and leave on for an additional 15 – 20 minutes. (Do not leave product on wood in excess of 30 minutes total.)
Wipe surface completely dry.
Ready for use in 6 – 8 hours.

Minwax® Antique Furniture Refinisher removes oil finishes, including shellac, lacquer and some early forms of varnish. Minwax® Antique Furniture Refinisher contains natural wood oils that penetrate and condition wood. Minwax® Antique Furniture Refinisher does not remove paint or polyurethane. The perfect product to refinish all your wood furniture.

1L - Sku 27342-91, Model 19003, $16.49 each

Application tool: steel wool
Removal: medium steel wool or synthetic stripping pad and rags
Cleanup: mineral spirits or paint thinner, following manufacture's safety instructions
Recommended uses: furniture, antiques, woodwork, cabinets, doors, paneling, accessories

Minwax® Paste Finishing Wax protects and adds lustre to any stained or finished wood surface.

Natural - Sku 27339-21, Model 85002, $13.49 each
Dark - Sku 27339-47, Model 86002, $13.49 each

Application tool: cloth
Dry time: 10-15 minutes prior to buffing
Cleanup: mineral spirits or paint thinner following manufacturer's safety instructions
Coats: 1 over a previous finish; 2 over raw wood
Recommended uses: furniture, antiques, woodwork, cabinets, doors, paneling, accessories
Colors: natural, special dark

DIRECTIONS: