Supplementary Life Safety Auxiliary Devices
(Kidde)
Kidde offers products designed for special situations.
This includes strobe light devices for the hearing impaired and heat alarms for
situations where smoke detection may not be the best solution.
We also sell smoke and carbon monoxide relay modules and adapters for those
wanting to interconnect between brands - all available on special order.
STROBE LIGHT, REMOTE VISUAL
SIGNALING DEVISE FOR SMOKE ALARM - DUAL MODE SL177i - 120V AC Direct Wire
The Kidde SL177i, used in conjunction with a smoke, heat or carbon monoxide
alarm, provides a bright visual signal to warn of a smoke, heat or CO
hazard. The Kidde Strobe light benefits the hearing impaired, allowing a
visual alert of a danger. This unit also includes a tamper resist pin that
helps to deter thief and tampering.
The Kidde SL177i is a 120VAC wire in unit that provides a visual warning
when part of an interconnected system.
Strobe Light
Remote Visual Signaling Device
120V AC Wire-In - Dual Mode
Quick-Connect 120 Volt AC Wire Harness included
For the Hearing Impaired
Bright 177 Candela Strobe Light - provides a visual warning when part of a
Kidde interconnected alarm system* - *Warning! This visual signaling device
has no detection means and must be interconnected with operating alarms.
Disconnecting or loss of AC power will render this signaling device
inoperative
Inter-connectable - Works with interconnectable Kidde, Fyrnetics, Lifesaver,
and Nighthawk AC wire-in alarms
5 Year Ltd Warranty
Interconnectable System
The Maximum protection only an InterConnectable System can offer: Every
floor. Every living space. Any place where a crisis could begin needs the
added security of an interconnectable warning system. Any unit that senses a
problem automatically triggers all units throughout the home immediately,
allowing extra time for escape.
Installation is simple: Unlike competitive products, the interconnectable
system requires no relay switches. No complex wiring. Just direct connect
and you're done.
Interconnects with all KIDDE, FYRENTICS, LIFESAVER and NIGHTHAWK smoke,
carbon monoxide and heat alarms, strobe lights and smoke and carbon monoxide
relay modules with interconnect capability. See enclosed users guide for a
listing by model number.
Strobe Light Features:
Provides a visual alarm to the hearing impaired. Strobe light is activated
when any Kidde, Fyrnetics, Lifesaver or Nighthawk interconnected smoke, heat
or carbon monoxide alarm is triggered.
Bright 177 Candela Strobe Light
Light level proven effective in waking the hearing impaired
1Hz Flash Rate
60 flashes per minute meets UL & NEMA standards
Smart Interconnect
Connects with up to 24 Kidde, Fyrnetics, Nighthawk or Lifesaver 3 wire
devices. Differentiates smoke and CO alarm signals with appropriate warning
Green LED indicator
Light verifies that alarm is receiving AC Power
Quick Connect
Installs and disconnects quickly with snap-on harness
Separate Trim Ring
fits all standard electrical box configurations
Tamper Resistant Locking Feature
To deter strobe light theft or removal
Must be Interconnected with Kidde, Fyrenetics or Lifesaver Alarms
Complies with the following standards:
Underwriters Laboratories (UL 1971)
Americans with Disabilities Act (ADA)
National Fire Protection Association (NFPA 72)
ANSI 117.1
Warning: Strobe light is extremely bright. Do not look directly at the light
or touch the lens when the light is flashing.
Technical Specifications:
Power Source: 120 VAC, 60 HZ
Electrical Rating: 100-130 VAC, 60HZ, 80mA standby 43 mA in rush, 2.2A peak,
580mA when operating
Flash Rate: 1 flash/sec
Light Output: 177 candela minimum
Temp Range: 32F (0C) to 120F (49C)
Wiring: Quick Connect plug with 8" pigtails
Warranty: 5 Year
Size: 5.6" in diameter, x 3" in depth
Weight: 1 lb
Interconnects: Up to 24 Kidde devices of which 18 can be initiating devices
Recommended Placement for the Hearing Impaired (MUST BE INTERCONNECTED WITH
KIDDE, FYRNETICS OR LIFESAVER ALARMS)
Locate the first strobe in the bedroom where a person who is hearing
impaired sleeps. The unit must be interconnected to smoke alarms near the
bedroom. If there are no alarms near the bedroom, then an interconnected
smoke alarm must be installed in the bedroom.
Locate additional strobe lights in any rooms where a hearing impaired person
might be present and need to be notified of an alarm condition (i.e. living
room, kitchen, bathroom, basement)
Note: Light intensity gradually decreases as the viewing angle is increased.
Consult chart in owner's manual to determine best location for strobe light
installation
FYRNETICS HEAT DETECTOR -
Supplementary Life Safety Device - 120V AC Direct Wire with Battery Backup
The Kidde HD135F is a 120VAC Wire-In Heat Alarm that responds to temperature
rather than smoke. The alarm will sound if temperatures rise above 135F. The
Kidde HD135F is interconnectable.
The Kidde HD135F 120VAC wire in heat alarm gives you and your family an
early warning to dangerous temperatures of 135F or more.
120 Volt Single or Multiple station with 9 volt battery backup
Interconnect (24) with quick connector
Ceiling White
135F Fixed Temperature
Limited 5 year warranty
Wire in with battery backup
Single or multiple station
Interconnect (24) with battery backup
Warning! NOT A LIFE SAFETY DEVICE. Smoke Detectors are recommended where
life safety is a factor. Heat Detectors will not protect against fire and
smoke and should only be used in conjunction with operating smoke detectors
NEW Standardized Audible Signal
Complies with the following authorities: Underwriters Laboratories (UL 539),
National Fire Protection Association (NFPA 72.2), California State Fire
Marshal (CSFM 72.54)
Full interconnect compatibility with:
Fyrnetics Smoke Alarm Models: 1235E and 1275E
Lifesaver Smoke Alarm Models: 1235, 1275, and 1285
Lifesaver Carbon Monoxide Tetector Model FYCO-3
Suitable for ceiling or wall mounting
Battery backup: continues protection in case of AC power failure
AC Power Light (green) - When on indicates 120 Volt AC power is being
delivered to the Heat Detector
Test Button - Tests heat detector circuitry and horn
Alarm Light (red) - Rapid flashing LED indicates which unit in the
multi-station installation is the originating alarm
Single or Multiple Station Capability - To use as a single station or
multi-connect up to 24 units (when one alarm sounds, all interconnect alarms
sound)
DC Battery Backup - 9V battery included
Low Battery Indicator - In the event of a "low" or "absence of" the alarm
battery, the heat detector will sound a warning "chirp"
Loud, piercing pulsating horn - To alert you quickly (85 decibels)
Separate Trim Ring - Fits all standard electrical box configurations
Tamper Resist Locking Pin - to deter theft
Quick-Disconnect - 120 Volt AC Connector
Warning! Removal of the heat detector battery and disconnecting or loss of
AC power will render this heat detector inoperative
Heat alarms are for situations where smoke detection may not be the best
solution.
Technical Specifications:
Power Source: 120VAC, 60HZ, 9V battery backup
Sensor: Heat
Audio Alarm: 85dB at 10ft
Temperature Range: -20F to +100F (-29C to +38C)
Humidity range: 5%-95% relative humidity (RH)
Size: 5" in diameter x 2" depth
Weight: 0.75lbs
Interconnects: Up to 24 Kidde devices of which 18 can be initiating devices
LED: Green, AC Power present, alarm mode; flashing Red indicates originating
alarm
Warranty: 5 year limited warranty
RELAY / POWER SUPPLY MODULE for
Kidde Smoke/CO/Heat Detectors/Alarms
Tech Specifications:
Electrical Rating - 120V AC 60 HZ 0.08 amp
Contact Rating - 10 amps @ 120 VAC, non inductive, 5 amps @ 30 VDC
DC Output - 5 MA Max (current limited)
Description: This module is only activated by a smoke alarm interconnect
signal. The relay portion of this module can be used to activate auxiliary
warning devices such as external bells and sirens, hallway or stairwell
lighting. It provides isolated, (no internal connection to 120 Volts AC)
normally open, and normally closed contacts.
The power supply portion can be used to connect spot type heat detectors
(Rate of rise or combined rate of rise and fixed temperature only) and
manual pull stations with interconnected multiple station alarms.
The model SM120X module is for use with the following interconnectable
models:
Smoke Alarms: 1235, 1235CA, 1275, 1275CA, 1276, 1276CA, 1285, 1285CA, 1296,
i12020, i12020CA, i12050, i1240CA, i12060, i12060CA, i12080, PE120, PE120CA,
P12000, and PI2000CA, RF-SM-ACDC
CO/Smoke Combo Alarms: KN-COSM-IB, KN-COSM-IBCA
Heat Alarms: HD125F, HD125FCA
all with red interconnect wires.
The module should be installed in a UL listed junction box. All connections
should be made by a qualified electrician in accordance with the
requirements of the national electrical code and/or any other local codes
having jurisdiction in your area.
Smoke Relay
Modules
Activates or deactivates auxiliary devices such
as bells, lights and ventilation systems
For use with all interconnected installations
that contain smoke alarms and smoke/CO combo units and heat detectors
The power supply portion of this module can be
used with manual pull stations, flow switches, and spot type heat
detectors
For use with Kidde/Lifesaver smoke detector
models P1235CA, P1275CA, PPE120CA, HD135F
CARBON MONOXIDE RELAY / POWER
SUPPLY MODULE for Kidde CO Alarms
Tech Specifications:
Electrical Rating - 120V AC 60 HZ 0.08 amp
Contact Rating - 10 amps @ 120 VAC, non inductive, 5 amps @ 30 VDC
DC Output - 5 MA Max (current limited)
Description: This module is only activated by a Kidde Carbon Monoxide alarm
interconnect signal. The relay portion of this module can be used to
activate auxiliary warning devices such as external bells and sirens,
hallway or stairwell lighting. It provides isolated, (no internal connection
to 120 Volts AC) normally open, and normally closed contacts.
The power supply portion can be used to connect spot type heat detectors
(Rate of rise or combined rate of rise and fixed temperature only) and
manual pull stations with interconnected multiple station alarms.
The model CO120X module is for use with the following interconnectable
models:
CO/Smoke Combo Alarms: KN-COSM-IB, KN-COSM-IBCA, KN-COB-IC, KN-COP-IC
Outer packaging is blue, in order to distinguish from Smoke Relay Module,
Model SM120X, which has black outer packaging.
This device will only activate when it receives a CO interconnect signal
from a compatible device. When in the activated mode (as a result of a CO
signal), this device will deactivate if it receives a smoke interconnect
signal from a compatible device. NOTE: Only the Carbon Monoxide portion of
the: KN-COSM-IB and KN-COSMIBCA
combo alarms will activate this module. If activation is required from the
Smoke Alarm portion of these alarms, use the SM120X module.
We welcome all inquiries on our products. Please use
Feedback form to
contact us.
Please note that all prices in all categories are
listed in Canadian Dollars. All items are subject to 15% Harmonized Sales
Tax (HST) when shipped to Nova Scotia, 13% Harmonized Sales Tax (HST) when
shipped to New Brunswick, Newfoundland or Ontario, 12% Harmonized Sales Tax (HST)
when shipped to British Columbia. All other
provinces/territories are subject to 5% Goods and Service Tax (GST). International and United States sales are
tax exempt (duty and brokerage fees, if applicable, are the responsibility of
the purchaser).
Unless picked up at our location, all items are subject to applicable freight charges (to be quoted).
Not all items can be shipped due to weight and size factors. Items marked
free shipping are for within Canada and the USA (with the exception of remote
locations)). We do not
ship chemical products or insecticides. All prices
subject to change without notice. Not all items may be available at all
times. We reserve the right to choose our customers and to limit
quantities if needed. Website is also subject to error. If a pricing
error is discovered it will be fixed, however we are not obliged to sell for the
error. Website pricing may differ from in-store pricing.
We accept VISA, Mastercard or American Express. You can also send a money order
or check, in which case we will wait for it to clear prior to shipping out the
goods. In some cases, Paypal will be used as a payment method.
.JPG)
.JPG)
.JPG)
.JPG)